Share This Article
Types of wall tiles can add aesthetics to your home’s interior and exterior. In the article below, let’s find the most professional wall tile technique with San Francisco Contractors!
What are wall tiles?
Wall tiles are tiles that are used on the wall vertically. Because this area is less affected than the floor, the quality requirements for wall tiles are usually not too high. Wall tiles will have a porous and lighter texture and focus textures on increasing the aesthetics of the wall surface. Usually, wall tiles will protect the wall and improve the aesthetics of the living space.
Regarding the question of whether we can use floor tiles for wall cladding? The answer is absolutely world. For large-sized, square-shaped floor tiles, homeowners can consider using them for exterior walls, fences, and house facades. The quality of high-quality tiles with Granite brick bones will help protect the front of the house against all environmental, weather, and climate impacts. As for the interior space, you should use only Ceramic tiles for wall cladding to ensure aesthetics and safety for your family members.
Choose wall tiles
Before learning about wall tile techniques, you need to know how to choose the right type of tile. You can refer to some tips for choosing beautiful and luxurious wall tiles below:
- Color: The first factor you must consider when choosing wall tiles is color. You can choose the most suitable color wall tiles based on feng shui, area, floor tile color, ceiling color, and space area. For example, if your home has a small area, you should choose bright colored tiles. Light colors will make your home more spacious and airy.
- Type: You must consider choosing the right tile for the space. For example, the living room should choose a different tile than the bedroom. You also need to pay attention to the degree of harmony of the interior design of the house so as not to create a feeling of being out of place, losing the aesthetics of the space.
How to properly install wall tiles
Step 1: Prepare the necessary materials
First, choose the type of wall tiles matching your preferences and living space. For example, ceramic tiles, granite, ceramic wall tiles, marble, and natural stone wall tiles… are some of the popular types of wall tiles today.
Wall tiles must meet quality, correct specifications, no errors, and sharp pattern lines to ensure aesthetics after being applied to the wall.
Next, prepare the tools to install the tiles on the wall, including a trowel, invoice or mortar bucket, rag, or sponge to clean the tiles, ruler, tile cutter, wire, and tile grout, and scale mortar.

You need to remove the protrusions of the wall surface that need to be tiled with stone tiles and add mortar to the recesses, ensuring the wall surface is flat and smooth. Check the height of the floor and the level of the wall to be tiling. From there, fix it by plastering mortar and cement.
Before tiling, you need to pay attention to plaster a layer of sand-cement mortar in the ratio of 1:3. Small bricks are attached directly to the wall. For large bricks, one must use iron hooks to anchor them to the wall. Remember to tile from the bottom up, not from the top. If you can install any row, fill it with mortar. If you can seat three or four tiles, use a ruler to check if it’s flat.
For the wall tiles to be solid, after facing the tile, you have to gently lean on the surface for about ten days, use a painting towel to wipe the surface, and use a bamboo stick to flatten the wall to remove the mortar stains on the wall. You can tap the ruler to make it even if it’s not flat. After finishing, mix cement water to clean the circuit.
Step 2: Align the brick wall margin to balance.
To ensure that the wall surface does not have an aesthetic error, you should close a straight cast iron bar to take the lower edge of the tile. If your wall is not limited in height, you can put the wooden stick on the floor at the size of the brick.
Then measure from the edge of the wooden bar to the height of each row of wall tiles. You use a pencil to mark the line of the symmetrical brick, then use a ruler to align the horizontal line and use a plumber to block the vertical line. With this marking, in addition to adjusting the wall tiles to be balanced “best,” you can also calculate the number of tiles consumed. One brick is counted if the position at the edge is more than half a brick.
Step 3: Plaster or use circuit glue to cover the wall
At this step, you plaster the wall in pieces with a width of about 0.5m2. From the starting point to spread out, use the wavy tile blade to create waves on the mortar. When laying the first brick, do not forget to gently press the brick so that the cannon overflows in the wall gap.
Step 4: Use tile adhesive to apply tiles on interior walls
The most crucial step in tiling on the wall is this step. Glue is used to locate the gap between two bricks close to each other, with a thickness of about 1mm and 1.5mm. Then, the circuit board has a thickness equal to the distance between the two bricks, into the corner, and then put the next bricks in. This method saves bricks and ensures aesthetics.
Step 5: Clean and sanitize the surface
After the wall tile is finished, clean the surface thoroughly. If the grout is not dry, proceed to clean the grout with tile adhesive on the surface of the tile. If it is necessary to cut the gauze, use a tile cutter to cut the tiles properly. Thus, avoiding cutting and breaking, wasting bricks, and consuming more materials for wall tiles.
San Francisco Contractors has just compiled to help readers with the most professional and technically correct wall tile technique. Hopefully, through this article, you can make your wall tiles for your space. If beyond capacity, do not hesitate to contact us to receive the best quality help.